Explore Sheet Metal Processes & Supplier Selection
When a drawing calls for a sharp aluminium flange and the first sample sits two degrees open, the debate is rarely about whether the brake “can form aluminium.” It is about how much aluminum springback compensation the shop was allowed to apply, and whether the bend-angle tolerance on the print left room for that compensation. Buyers who treat springback as a shop-floor trick get parts that miss the mating panel. Buyers who write overbend variables into the RFQ get samples that match the assembly stack.
This page stays on what overbend has to correct, how R/t and temper widen the window, why grain direction belongs on the drawing, what bend-angle tolerance is realistic, and how to RFQ a shop that forms aluminium regularly. For alloy formability and why aluminium springs more than steel at a systems level, see aluminum sheet metal fabrication: alloy, springback and dissimilar metals.
What does overbend have to correct on aluminium?
It corrects elastic recovery after the punch lifts.
Overbend is the extra angle the brake forms so that, once the elastic portion of the bend recovers, the part sits at the target included angle. Aluminium recovers more than mild steel for the same stress, so the same flange that lands true in CRS often opens when the blank is 5052 or 6061.
Compensation is not a single “aluminium factor” stored on a sticky note. It depends on thickness, inside radius, alloy and temper, tooling style (air bend versus bottoming), and how far the bend sits from free edges or prior forms. A shop that only logs final angle without recording punch depth, die opening and measured springback cannot reproduce the first good sample on the next lot.
Drawing practice should treat the target angle as the as-received geometry after springback, not the ram angle the operator dials. Dimensioning conventions for formed parts sit under ASME Y14.5, while equipment and process capability discussions for metal forming appear in industry resources from the Association for Manufacturing Technology on forming. Neither source replaces your shop’s measured overbend table; both explain why prints that demand an exact angle with no process note invite scrap.

How do R/t and temper widen the springback window?
Larger R/t and harder tempers increase recovery.
The radius-to-thickness ratio governs how much of the bend is elastic versus plastic. A generous inside radius relative to thickness leaves more elastic recovery, so springback grows even when the alloy is formable. A tighter radius increases plastic strain and can reduce springback, but it also raises crack risk in heat-treatable grades.
Temper matters as much as alloy family. Soft O-temper sheet yields more readily and usually needs less overbend than a harder H-temper of the same alloy at the same R/t. Heat-treatable grades in T4 or T6 condition bend less generously; shops often enlarge the inside radius or move critical flanges to a softer temper and age after forming when strength is required. Material property references published by suppliers such as Novelis rolled products and Hydro aluminium list temper designations; they do not tell you the overbend degrees for your die set.
In RFQ terms, stating “aluminium, formable” is not enough. Name the alloy, temper and thickness, and call out any flange where R/t sits near the shop’s crack limit. When the same part mixes thin cosmetic panels with thicker structural flanges, expect different compensation values on the same blank. 6CProto reviews bend radii against the intended alloy during free DFM before quoting forming and bending work from its Zhongshan facility and Guangdong partner network.
Why does grain direction belong on the drawing?
Rolling direction changes bend behaviour and marking risk.
Rolled aluminium sheet is anisotropic. Bending across the grain usually behaves differently from bending with the grain: crack risk, springback magnitude and surface orange-peel can all shift. Cosmetic brushed panels add a second directional constraint because grain and brush lines both show after anodizing.
Put the preferred grain direction on the drawing relative to primary bend lines, or state that the shop may nest for yield unless a cosmetic face forbids it. Leaving grain unmarked forces the programmer to choose nesting for sheet utilisation, which may place a critical bend parallel to the rolling direction on one lot and across it on the next. Angle drift between lots then looks like “inconsistent springback” when the blank orientation changed.
Measurement practice for formed parts is discussed in resources from the NIST Manufacturing Extension Partnership. Use those habits on first-article flanges: measure the same bend with the same datum scheme after the part cools, and record blank orientation. Drawing notes that say “grain optional” should mean it; if cosmetically critical faces exist, say so explicitly.
What bend-angle tolerance is realistic for aluminium?
Allow process-capable bands, not steel-era exactness.
Prints that carry ±0.5° on every aluminium flange often exceed what air-bend processes hold without secondary wipe or CNC correction. Realistic tolerances depend on thickness, length of flange, tooling and whether the angle is functionally critical or only a clearance feature. Critical mating flanges deserve tighter callouts plus a note that the shop may iterate overbend on first article. Non-critical returns can carry wider bands so the operator is not chasing cosmetic variation.
Separate angle tolerance from flange length and hole-to-bend distance. A flange that is long and thin will show more variation along its length than a short stiff return. Hole patterns near bends inherit blank stretch and springback; if those holes locate an assembly, either form first and machine after, or open the positional tolerance. Machine features after forming when the controlled face cannot be held through the brake, using CNC milling where needed.
Industry drawing standards from ASME expect unambiguous datums and tolerances; they do not invent a universal aluminium bend chart. Ask the quoting shop what angle band their aluminium process historically holds on comparable R/t, and write that band into the RFQ instead of copying a steel drawing template.

How should you RFQ a shop that forms aluminium regularly?
Ask for measured overbend evidence, not a verbal assurance.
An RFQ that only attaches a STEP file invites quotes based on steel habits. Include alloy and temper, thickness, inside radii, cosmetic faces, grain preference, bend sequence constraints, and which angles are assembly-critical. Ask whether first-article price includes iterative overbend adjustment and whether subsequent lots freeze the punch program.
Useful supplier questions are concrete: which press-brake controllers and tooling libraries they use for aluminium; whether they bottom or air-bend the radii on your print; how they document springback for repeat orders; and whether they will mark grain on blanks when the drawing requires it. Equipment makers such as Amada and LVD publish press-brake capabilities; matching a brand name is less important than matching process records for aluminium.
Blank quality also feeds springback consistency. Edge condition and heat tint from prior laser cutting can change local yield near the bend line. State whether film stays on through forming and which faces must remain free of brake marks. Design guidance for nest and bend planning is collected under sheet metal design guides.
What process records freeze aluminum springback compensation between lots?
Freeze depth, die set and blank orientation with angle.
A first-article flange that lands on target is worthless for production if the traveler only stores the final angle. The next shift needs the same punch, die opening, programmed depth or crowning correction, blank grain mark and film state. Without those fields, operators recreate a steel default and reopen every return.
Build a short aluminium bend card per part number: alloy/temper lot identity, thickness check, inside radius tool ID, target angle, measured overbend or depth, inspection method and cosmetic-face protection. Attach a photo of the setup when the brake uses unconventional gooseneck or radius tooling. When a material lot changes hardness within the same temper label, re-run a single flange coupon before releasing the full nest.
Buyers should ask whether that card is included in the quoted first-article package. Shops that form aluminium regularly already work this way for aerospace and electronics brackets; shops that dabble in aluminium often skip it until the second rejected lot. Press-brake builders such as Amada and LVD document controller features that store angle corrections — useful only if your supplier actually saves the programme against the part revision.
Dimensional reporting should cite the same datums used on the drawing after springback, not a soft tape measure on an unsupported flange. If a critical angle feeds an assembly stack, require a fixture or digital protractor setup note so customer and supplier measure the same way. That discipline prevents false “out of tolerance” claims that are really measurement method drift.
Finally, separate engineering changes from process tweaks. A one-degree overbend adjustment to hit the print is a process freeze; changing the inside radius on the model is a revision that may reopen formability review. Keep both trails visible so quality and purchasing know which document controls the next PO.
Where does this sit in aluminum sheet metal fabrication?
Springback compensation is one process slice inside a wider aluminium fabrication decision set that also covers alloy choice, dissimilar-metal joints and finishing. Keep this page on overbend variables and drawing allowances; use the hub for the broader alloy, galvanic and cost context in aluminium forming springback and related fabrication topics.
When the model is ready, name the alloy, temper, radii and critical angles, then request a quote for aluminium forming. Email projects@6cproto.com or WhatsApp +86 180 2219 4001 for DFM feedback before the first blank is nested.
FAQ
Can software alone set aluminum springback compensation without a first article?
Simulation and controller libraries give a starting overbend, but aluminium lots, tooling wear and actual R/t still move the result. Treat software output as a first-article seed, then freeze the measured punch depth once samples meet the print. RFQs that forbid sample iteration should widen angle tolerances accordingly.
Does bottoming eliminate the need for overbend on aluminium?
Bottoming reduces springback relative to a light air bend, but it does not remove elastic recovery, and it raises tonnage and marking risk on soft aluminium. Many shops still apply a smaller compensation and protect cosmetic faces. Ask which method the quote assumes before comparing prices.
Should bend angle be inspected before or after anodizing?
Measure functional angles on the formed blank against the drawing datums, then confirm after coating only if coating growth or masking could affect a mating feature. Anodizing does not usually “fix” springback, but handling and racking can distort thin flanges. State the inspection stage on the RFQ.
What information belongs in a repeat-order traveler for aluminium bends?
Record alloy/temper lot, blank orientation, die opening, punch radius, programmed overbend or punch depth, measured first-piece angles, and cosmetic-face protection. Without those fields, the next operator may recreate the steel default and reopen every flange.

