Michael Wang

Founder & Mechanical Engineer

As the founder of the company and a mechanical engineer, he has extensive experience in advanced manufacturing technologies, including CNC machining, 3D printing, urethane casting, rapid tooling, injection molding, metal casting, sheet metal, and extrusion.

Table Of Contents

Explore Sheet Metal Processes & Supplier Selection

A blind rivet can pull and break its mandrel without proving that it is the correct length for the joint. Rivet grip range refers to the assembled material thickness a particular rivet is designed to fasten. The relevant stack can include coatings, washers, shims or compliant layers, so two nominal sheet thicknesses rarely tell the complete story.

The practical task is to keep the real stack inside the selected product’s limits and then verify that setting produces the intended joint. This guide focuses on blind rivets and draws clear boundaries around solid rivet rules, overall rivet length and special multi-grip products. It also considers what happens when the stack changes between prototype and production.

How should rivet grip range be checked?

Measure the assembled stack, then use the exact datasheet.

Compare the least and greatest effective joint thickness with the selected rivet’s stated grip range, including layers that change the stack or its behavior during setting.

Measure at the fastener location after the joint is brought into its intended assembled condition. A burr between sheets, a gap caused by springback or a thick coating bead can create a local stack unlike the nominal design. Do not use fastener pull to compensate for an unspecified large joint gap.

The POP rivet catalog identifies grip as a product selection parameter rather than a universal formula from body length. For sheet work, coordinate the hole and assembly condition with the sheet metal fabrication plan. The stack measurement should reflect how the actual components meet, not how separately measured flat coupons happen to add together on a desk.

Measure enough locations to capture local formed variation where relevant. A remote flat region may not represent the stack beside a bend, embossment or distorted mounting flange in production.

Grip range versus rivet length

Overall body length and grip range are related within a rivet design, but they are not interchangeable specifications. The tail must form appropriately during installation, and the selected head, body and mandrel system influence the usable range. Two rivets with equal nominal length can have different approved grips.

Select by the manufacturer’s complete part number, diameter, head style, material and range. A multi-grip product deliberately covers a stated range, but it does not remove all stack limits. The VGrip product datasheet illustrates how a particular family documents its grip capability; its values should not be transferred to another blind rivet.

Solid rivet protrusion rules answer a different installation question and should not be applied to ordinary blind rivet length selection. Similarly, semi-tubular rivets and self-piercing systems have their own geometry and tooling requirements. When a purchasing record says only “long rivet,” replace it with an approved product specification and a defined stack interval before a substitute is accepted.

Preserve the full fastener designation when a supplier changes packaging or catalog format. A shortened description can omit the head style or material that defines the approved joint.

rivet grip rangeRivet Grip Range01Measure the real assembledstack02Grip range versus rivetlength03Coatings and compressiblelayers04Inspect the formed jointwithout over settingCheck these interfaces against the actual material, geometry and acceptance.
Related engineering checks for rivet grip range; the worked example and drawing requirements define the actual scope.

Coatings and compressible layers

Coatings add thickness, while soft layers can change thickness under installation load and later in service. Include washers, sealants, gaskets and protective films that remain in the finished joint. Exclude temporary films only when the assembly instructions actually remove them before fastening.

A compliant layer may initially fit the grip range yet relax after setting, reducing clamp behavior or permitting movement. The correct response is not automatically a longer rivet. Review whether the joint needs a compression limiter, a different stack arrangement or a product intended for the substrate. The POP product family information distinguishes several constructions, including designs for particular joining needs; the selected product’s detailed instructions remain controlling.

Document whether thickness is specified in the free state, under a defined assembly condition or after cure. If sealant squeezes out, the effective grip and sealing path both need validation. Check representative production coatings and actual cure conditions rather than assuming that an uncoated prototype predicts the final assembly.

If an adhesive cures after fastening, evaluate the final condition as well as the installation stack. Cure shrinkage or relaxation can change behavior without changing nominal sheet dimensions.

Inspect the formed joint without over setting

Inspect the formed joint using the fastener manufacturer’s criteria and the drawing’s functional requirements. Relevant observations can include head seating, blind side formation, stem position and local damage, depending on the product. A mandrel break sound is not a universal acceptance test.

The tool, nosepiece, stroke and pull characteristics must match the fastener system. Stanley’s rivet installation tool information shows why tool selection belongs with fastener selection. Do not attempt to correct a wrong grip choice by repeatedly pulling or reworking a set rivet unless the approved process specifically allows it.

Structural blind rivets can have features that ordinary blind rivets do not share. For example, the Monobolt product description identifies a particular mechanically locked stem construction. That feature is product specific and should not be inferred for a generic blind rivet. Record visible acceptance requirements in language an inspector can apply to the selected part number, and define how inaccessible blind side features will be verified during qualification.

Do not use a second setting attempt as an informal inspection method. It can alter the fastener or sheet and destroy the original evidence needed to diagnose the installed condition.

Material and joint choice comparison table

The joint material affects both grip selection and what failure looks like. A fastener strong enough in isolation can still pull through a thin sheet or damage a soft panel. Compare the complete joint rather than choosing the largest available rivet and assuming greater reliability.

Stack condition Selection concern Verification focus
Two rigid metal sheets Total thickness, hole fit and material compatibility Head seating and blind side formation
Coated sheets Actual coating buildup and cure condition Local damage and corrosion protection
Soft or thin layer Pull-through and compression Panel deformation and retained function
Sealed assembly Sealant behavior and leak path Leak test under defined conditions

Consider corrosion compatibility between the fastener, sheets and service environment. A sealed style is not a complete enclosure sealing system by itself. Define the final acceptance in the fabricated assembly specification, including any protective treatment disturbed by setting. Keep nominal fastener strength separate from the demonstrated performance of the real stack.

For dissimilar materials, review the actual wet exposure and protective system. Material compatibility is an assembly question, not something proved solely by the fastener body material description alone.

Dimensioned joint section and assembly sequence

Assume a hypothetical joint contains two sheets, each 1.5 +/- 0.1 mm, and two retained coating layers, each 0.05 +/- 0.01 mm. Assume no gasket, washer, assembly gap or compressible adhesive. The minimum nominal stack calculation is 1.4 + 1.4 + 0.04 + 0.04 = 2.88 mm; the maximum is 1.6 + 1.6 + 0.06 + 0.06 = 3.32 mm.

The selected rivet’s specified grip interval must cover the intended production stack under its documented installation conditions. This example does not identify a suitable rivet because diameter, material, head, loads and installation system remain unspecified. It only shows why selecting from the 3.10 mm nominal sum alone is incomplete.

Now add a washer on the blind side: its tolerance must enter the same calculation, and installation access must be checked. If a prototype lacked the production coating, qualify the updated stack before release. Keep the arithmetic with the drawing revision so that a later layer change triggers a deliberate selection review.

Keep retained layers explicit in the bill of materials. A temporary spacer used during prototype assembly should not silently become part of the production grip calculation or installation process.

Validation loads and acceptance observations

Define validation loads from the assembly’s real duty. Shear, tension, peel, vibration and thermal cycling are different demands; a simple pull test may not represent them all. Fastener catalog strength values are not automatically joint allowables because sheet thickness, edge distance, hole condition and load sharing influence failure.

Test representative worst case stacks where appropriate, including the thinnest and thickest permitted conditions. Observe whether failure occurs in the fastener, sheet, coating or interface. Record movement and permanent deformation as well as the final failure load when those matter to function. An assembly can become unacceptable through looseness before the rivet itself breaks.

Relate observations to the agreed inspection and tolerance requirements. Preserve the actual installed fastener identity and tool setup with the results. Orbitform’s fastener process FAQ is a reminder that forming and riveting methods have distinct process requirements; do not mix acceptance rules from a different rivet construction when evaluating a blind riveted sample.

Inspect the hole after a failed trial when sheet damage is possible. A fastener replacement in an enlarged hole may no longer represent the originally qualified joint geometry and fit.

Coordinate-measuring probe above a round component held on a fixture
Finished-part geometry needs acceptance independently of the setting operation.

Drawing notes for the production joint

State the approved fastener part number or an equivalence specification detailed enough to prevent silent changes in grip, head or mandrel behavior. Identify the assembled stack range, hole condition, material and any coating or sealing layer retained at the joint. Include access restrictions for both installation and inspection.

The assembly sequence should explain how parts are located and brought together before setting. If temporary clamps establish the stack, define that condition and verify that it is practical in production. Mark any surfaces where cosmetic damage or local deformation is restricted, and define disposition when a rivet is removed.

For rework, specify whether the hole must be rechecked, enlarged or rejected after removal; drilling out a rivet can change the joint. Record the qualification basis for a replacement fastener rather than allowing an installer to choose the next available length. Keep drawings, bill of materials and tool instructions synchronized so that the approved grip range remains meaningful beyond the initial prototype.

Define traceability appropriate to the joint importance, including fastener lot and installation setup where required. This helps isolate a change without assuming every rivet shares the same condition.

FAQ

How far should a blind rivet protrude before setting?

Use the chosen blind rivet manufacturer's grip range and installation instructions rather than a general protrusion rule. Protrusion formulas commonly associated with solid rivet shop heads do not transfer directly to blind rivets, whose bodies and mandrels form differently. Confirm the complete part number and measured stack, then verify the installed result on representative components. If access prevents checking the blind side during production, establish a qualified setup and appropriate inspection method before release.

Does a multi-grip rivet cover any sheet thickness?

No. Multi-grip means the product is designed for a stated range, not an unlimited one. Its diameter, head, material and installation tool still need to suit the joint. Check both ends of the permitted stack interval and confirm any restrictions for thin or soft material. A multi-grip product can simplify a bill of materials, but it should not conceal uncontrolled gaps, coating buildup or an assembly stack that changes without a documented engineering review.

Why are rivets still used instead of welding?

Rivets remain useful where access, material combinations, surface treatments or assembly sequencing favor a mechanical joint. They can join parts without a weld heat input, although they introduce holes, fastener loads and their own inspection requirements. The best joining method depends on the complete assembly and service demands. Compare stiffness, sealing, corrosion, fatigue and repair needs rather than assuming that riveting is obsolete or that a welded joint is automatically stronger in every configuration.

Conclusion

A reliable grip choice begins with the real assembled stack and ends with the installed joint. Match the entire tolerance interval to a specific rivet datasheet, including coatings and retained layers, and keep product construction separate from nominal body length. Confirm that the tool and nosepiece suit the chosen fastener.

Qualification should examine the joint’s actual failure modes and functional limits, not only whether the mandrel breaks. Document the stack, installation condition and rework rules so a later coating or washer change does not become an unnoticed process change. For a sheet assembly review, send the joint section, fastener specification and expected service loads for quotation. This gives manufacturing a defined assembly to assess and provides inspection with an observable acceptance target.

{“@context”: “https://schema.org”, “@type”: “FAQPage”, “mainEntity”: [{“@type”: “Question”, “name”: “How far should a blind rivet protrude before setting?”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “Use the chosen blind rivet manufacturer’s grip range and installation instructions rather than a general protrusion rule. Protrusion formulas commonly associated with solid rivet shop heads do not transfer directly to blind rivets, whose bodies and mandrels form differently. Confirm the complete part number and measured stack, then verify the installed result on representative components. If access prevents checking the blind side during production, establish a qualified setup and appropriate inspection method before release.”}}, {“@type”: “Question”, “name”: “Does a multi-grip rivet cover any sheet thickness?”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “No. Multi-grip means the product is designed for a stated range, not an unlimited one. Its diameter, head, material and installation tool still need to suit the joint. Check both ends of the permitted stack interval and confirm any restrictions for thin or soft material. A multi-grip product can simplify a bill of materials, but it should not conceal uncontrolled gaps, coating buildup or an assembly stack that changes without a documented engineering review.”}}, {“@type”: “Question”, “name”: “Why are rivets still used instead of welding?”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “Rivets remain useful where access, material combinations, surface treatments or assembly sequencing favor a mechanical joint. They can join parts without a weld heat input, although they introduce holes, fastener loads and their own inspection requirements. The best joining method depends on the complete assembly and service demands. Compare stiffness, sealing, corrosion, fatigue and repair needs rather than assuming that riveting is obsolete or that a welded joint is automatically stronger in every configuration.”}}]}