Explore Sheet Metal Processes & Supplier Selection
A hole appearing midway along a thin welded seam is a production symptom, not a complete diagnosis. The edge may have been poorly supported, the gap may have opened after tacking, or heat may have accumulated as the sequence progressed. Changing the machine setting without preserving those observations can hide the cause and produce another defect elsewhere.
Thin sheet metal welding burn through requires a joint-level review. The target is a continuous accepted connection with the required fusion and final geometry, rather than simply the absence of visible holes. A colder-looking bead can still fail if the correction prevents adequate joining.
Begin by marking where the hole occurred relative to starts, stops, tacks, clamps and changes in section. Save the part and the process record. That map guides a useful trial and helps distinguish a local fit problem from a condition affecting the whole seam.
For the manufacturing context, see sheet metal fabrication. This investigation addresses thin-joint preparation, heat control and the evidence needed to accept a corrected route. It does not provide a universal welding schedule or authorize repair of a component whose governing requirements prohibit it.
Gap and edge preparation
Check the joint before reducing welding energy.
Measure the actual gap, edge condition and local sheet thickness at the damaged location, then compare them with an undamaged region produced under the same documented setup.
A locally open gap changes how much material and support are available beneath the arc. A rough, thinned or poorly matched edge can make a nominally consistent seam behave differently along its length. Record both the prepared condition and the condition after tacking; they may not be identical.
Miller’s thin-sheet MIG and TIG guidance emphasizes controlling heat while retaining adequate mechanical strength. Use that balance to avoid treating minimum energy as the objective. The joint still has to form the required connection.
Inspect the cutting and deburring operations for unintended local thinning. Cleaning must suit the material and coating; removing contamination is different from grinding away a substantial edge. If a fit correction is proposed, define the permitted finished gap and how it is held during welding. An acceptable gap at the first tack does not demonstrate an acceptable gap at the point where burn through occurred.
Heat input along a thin joint
The damaged location may reflect the welding history of the seam. Starts, pauses, repeated passes and nearby welds change the local thermal condition. Compare where burn through occurs in the sequence before assuming one global setting explains it.
Miller’s MIG defect troubleshooting guide identifies excessive heat as a cause of burn through and discusses travel speed among the relevant controls. These are directional troubleshooting factors, not numerical instructions for every alloy, thickness or transfer mode.
When testing a correction, preserve the actual process identity and record the variables that were changed. A faster travel speed, a revised sequence and a different gap introduced together may improve the appearance without showing which change was necessary. It can also create inadequate fusion that remains invisible from the face.
Treat accumulated heating separately from instantaneous machine settings. A development coupon welded from a cold start may not represent a seam reached late in an assembly cycle. Reproduce the relevant starting condition and adjoining operations when establishing the corrective route. State the acceptance requirement first so process adjustments are judged against joint performance and geometry together.

Backing and joint access
Backing can alter support and heat flow at the root, but its effect belongs to the specific arrangement. Review contact, material compatibility, access and the ability to remove it. A loose backing strip that contacts one region and leaves another unsupported can introduce variation rather than control it.
Check the root side of the assembly model. The backing device, clamps and welding tool need usable space throughout the seam. A proposal demonstrated on an open coupon may be impossible inside a closed enclosure or after neighboring parts are installed.
Identify whether backing is temporary or remains in the product. Permanent material changes the delivered assembly and may affect corrosion, cleaning or downstream finishing requirements. It therefore needs design approval rather than being treated as an invisible shop aid.
For a fabricated assembly, review the complete operation order before adopting backing as the solution. Include insertion and withdrawal paths and access to the surface that requires inspection. Where a reusable device is proposed, define the condition and cleanliness that must be maintained for repeat production.
Inspection and repair disposition
Separate the decision to investigate from the decision to repair. A damaged trial part can reveal the failure mechanism, but a production repair must comply with the product’s drawing, contractual requirements and applicable procedure. Filling the visible opening does not by itself establish acceptable remaining thickness or fusion.
Map the damaged area before any grinding or additional welding. Record whether the edge has receded, whether cracking is visible and whether the surrounding part has moved. Those observations may disappear during rework and become impossible to reconstruct from the final photograph.
TWI’s weld-imperfection discussion distinguishes lack of fusion, porosity, cracking and other flaw types, and discusses validating inspection using representative defects. The distinction matters because a method chosen to find an open hole may not establish freedom from a different imperfection after repair.
Agree the inspection route for the repaired condition before proceeding. The method must suit the material, thickness, geometry and specified defect acceptance. Where the governing requirements prohibit repair or the damage cannot be characterized adequately, replacement may be the appropriate disposition. Keep that decision attached to the affected part identity.
Gap, backing and thermal conditions on the joint drawing
The joint drawing should connect the finished geometry with the process constraints that influence it. A nominal material thickness alone does not describe a locally thinned edge, a variable gap or a backing arrangement. Identify which dimensions are product requirements and which are controlled manufacturing conditions.
Use a matrix to expose missing information before the next trial. Assign the actual acceptance limits from the released design and procedure rather than using generic thin-sheet values.
| Condition | Where to establish it | Evidence needed |
|---|---|---|
| Edge and gap | After preparation and after tacking | Location-based fit record |
| Backing contact | Root side during welding | Fixture and access review |
| Thermal sequence | Starts, stops and neighboring welds | Trial sequence record |
| Finished joint | Specified inspection state | Geometry and weld acceptance results |
The ASME drawing framework supports a clear expression of finished geometric intent. It does not establish an acceptable welding gap or defect size. Keep those requirements in the appropriate controlled specification and reference it unambiguously from the drawing.
Reproducing the damaged seam in a development trial
Consider a hypothetical thin enclosure seam that opens near its unsupported end after several nearby welds have been completed. A short cold coupon with perfect edge contact will be a weak reproduction of that condition. It may show that welding is possible while failing to challenge the suspected mechanism.
Build a development specimen that represents the relevant edge preparation, restraint and assembly sequence. Include the least favorable permitted fit-up if that is the boundary being qualified. Record the condition before the seam starts and at the stage corresponding to the damaged location.
Change one investigative variable deliberately, such as support arrangement or sequence. Once a workable route emerges, demonstrate the combined approved condition and the required inspection evidence. Investigation trials and acceptance trials have different purposes and should be labeled accordingly.
NIST’s measurement-process variability discussion provides context for separating variation between parts from variation introduced by the inspection process. Repeated gap or distortion measurements should use consistent references and handling. Otherwise a moving measurement setup may appear to confirm or disprove a welding correction that it cannot reliably distinguish.
Accepting weld integrity and released sheet geometry
Evaluate the corrected seam against its required functions. Depending on the design, these may include load transmission, leak resistance, appearance and alignment of adjacent interfaces. Passing one does not prove the others, and a visually smooth repair may conceal an unacceptable geometry change.
Define the inspection state. A thin enclosure held against a rigid fixture can appear flat even when it springs after release. Record free-state geometry where that is the drawing requirement, and distinguish it from any specified restrained condition.
Report the location and nature of each observation. If the acceptance includes a mechanical test, explain how the specimen is loaded and what failure or displacement is permitted. If sealing is required, give the agreed test conditions rather than using the word sealed as an acceptance method.
NIST’s uncertainty-analysis guidance explains why measurement quality affects fitness for a decision. Apply that principle to local thickness, distortion and any load result. A small apparent difference after a correction needs a method capable of resolving it. Retain the relevant images and instrument setup with the report so the conclusion can be reviewed.

Burn-through evidence for the manufacturing review
Send the seam geometry, material specification and assembly sequence with the quotation request. Identify any restricted root access, backing limitations, coating condition and finished interfaces affected by distortion. Explain whether the job is a new development route or production to an existing qualified specification.
For a troubleshooting request, provide photographs taken before repair, a map of defect locations and the recorded process conditions. Include a conforming comparison region when available. This makes the request more useful than an isolated close-up of a hole with no indication of where it appeared in the operation.
Define whether process development, trial specimens, repair assessment and inspection are included in the requested scope. These activities require different deliverables. State the acceptance owner and the document that controls release.
The standards and tolerances reference can support that discussion, but the joint-specific requirements must remain in the supplied specification. Ask manufacturing to identify unresolved fit and access assumptions with its proposal. That exposes the conditions on which a repeatable weld depends before a purchase order treats them as settled.
FAQ
Can a ground flush repair hide unacceptable thinning?
Yes. A flush surface describes appearance relative to its surroundings, not the remaining wall thickness or the quality of the connection beneath it. Grinding can remove additional material from an already damaged region. Define the approved repair and inspection method before reworking a production part. If the remaining section or fusion cannot be demonstrated against the governing requirement, a visually neat repair should not be accepted on appearance alone.
Should a prototype with burn through be discarded immediately?
Preserve it long enough to record the mechanism and decide its disposition. The location, edge recession and surrounding distortion can provide useful development evidence. Clearly segregate it from accepted parts and avoid additional work that destroys the observations before review. Whether it can later be repaired depends on the product requirements and an approved route; its value as an investigation sample does not make it acceptable for delivery.
Can a different welding process remove the need for fit control?
No. A process change may alter the workable range, tooling and thermal behavior, but the joint still needs defined preparation, access and acceptance conditions. Evaluate the proposed process on representative specimens rather than transferring approval from a different joint. Include any changed filler, shielding, backing and inspection assumptions in the review. The useful comparison is the complete repeatable route and delivered condition, not a process name by itself.
Conclusion
Preventing recurrence requires a documented relationship between fit-up, support and the welding sequence. Keep enough energy and process control to form the accepted joint while avoiding the local condition that caused the material to collapse. The absence of a visible hole is only one observation in that assessment.
Use representative trials to demonstrate the correction, then inspect the condition that the product drawing actually accepts. Preserve any repair limitations and the evidence used to authorize release. When a changed process cannot meet both weld integrity and final geometry, revise the joint or manufacturing route before normal production resumes.
For a DFM and quotation review, upload the assembly CAD, seam details and weld acceptance specification. Include photographs and the sequence record when resolving burn through so 6CProto can evaluate the real access and fit conditions alongside the requested finished part.

