Explore Sheet Metal Processes & Supplier Selection

Buyers still write “18 gauge” on prints, then discover the stainless blank is not the same thickness as the mild-steel blank their prototype used. A sheet metal gauge chart exists because gauge numbers are a legacy naming system—not a single universal millimeter. This page gives practical thickness tables for common gauges, explains why steel, stainless, and aluminum diverge, and shows how to call out thickness so laser cutting and bending quotes stay accurate.

Why does sheet metal gauge confuse engineering teams?

Gauge numbers are not metric or inch standards.

They are historical size codes. A higher gauge number means a thinner sheet within a given system, but the decimal thickness for “18 gauge” depends on whether you mean standard steel, galvanized steel, stainless, or aluminum. Metal Supermarkets’ public chart (sheet metal gauge chart) states the same rule of thumb: convert gauge to actual thickness before you design bends or calculate stiffness.

For procurement and DFM, the safest habit is to put decimal thickness (in and mm) on the drawing as the governing requirement, and keep gauge only as a colloquial note if your plant still stocks by gauge.

Sheet metal gauge chart for standard steel (selected sizes)

These values follow widely published Manufacturers’ Standard Gauge figures for steel sheet (inches and approximate mm). Always confirm mill certificates for critical jobs.

Gauge Steel thickness (in) Steel thickness (mm approx.)
11 0.1196 3.04
12 0.1046 2.66
14 0.0747 1.90
16 0.0598 1.52
18 0.0478 1.21
20 0.0359 0.91
22 0.0299 0.76
24 0.0239 0.61

So 18 gauge steel thickness is about 0.0478 in (1.21 mm), 16 gauge steel thickness about 0.0598 in (1.52 mm), and 11 gauge steel thickness about 0.1196 in (3.04 mm). Reference tables on engineering sites such as CustomPartNet’s gauge chart and Engineers Edge publish the same family of steel decimals (access may vary by network).

Aluminum alloy sheet and rod material samples used for fabricated parts
Sheet and bar stock samples—thickness callouts should match the alloy system you actually buy.

How do stainless and aluminum gauges differ from steel?

Same gauge number, different decimals.

Stainless and aluminum often use different gauge tables. For example, published aluminum gauge charts list 18 gauge near 0.0403 in, while stainless charts list values that also diverge from carbon steel. That is why swapping “18 ga steel” for “18 ga aluminum” in a CAD model without updating bend deductions leads to wrong flat patterns.

When you source from a China fab partner, write: `Material: 5052-H32 aluminum, thickness 1.27 mm (0.050 in)` rather than only `18 ga Al`. Stock in Asia is frequently sold by millimeter thickness even when US drawings still say gauge.

Which gauge should you pick for enclosures and brackets?

Start from stiffness, mass, and joinery—not from habit.

Thicker gauges (lower numbers) resist denting and support larger unsupported spans, but they raise laser cut time, bend tonnage, and shipping weight. Thinner gauges form sharper cosmetics on small chassis but buckle under connector loads. A practical pattern for many electronic enclosures is 16–20 gauge steel or the millimeter equivalent in aluminum, then validate with a quick FEA or a physical kick test on the first article.

Also plan fastening: PEM nuts, rivets, and weld nuts each prefer a thickness window. If you will powder coat, remember coating build can close holes—compensate in the flat pattern.

How does thickness change laser cutting and bending quotes?

Thickness drives power, pierce time, and min flange length.

Laser cutters slow down and may change assist gas strategy as thickness rises. Kerf and heat-affected zone also change hole-to-edge rules. On the press brake, inside bend radius rules of thumb scale with thickness; a bend that was fine at 1.0 mm may crack or distort at 2.0 mm without a larger radius or annealed temper.

Tell the fab shop your cosmetic faces, grain direction needs, and whether tabs must stay flat after forming. Link process scope on sheet metal fabrication and forming & bending when you request a multi-op assembly quote.

Aluminum sheet metal part with chemical film surface finish
Formed aluminum part—finish and thickness should be specified together for consistent fit.

Should drawings still list gauge at all?

List decimal thickness as governing; gauge as optional.

Purchasing teams that stock by gauge can keep a dual callout: `1.21 mm / 0.0478 in (18 ga CRS ref.)`. Incoming inspection should measure thickness, not argue about which chart the mill used. For regulated or high-reliability builds, require mill certificates and note the acceptance band (for example ±0.05 mm) instead of relying on gauge tolerance folklore.

NIST’s weights and measures resources (NIST PML Weights and Measures) reinforce a broader point useful to fab buyers: measurement systems and unit clarity prevent downstream disputes—even when the commodity still uses legacy names like “gauge.”

Sheet metal prototyping without locking a mill run

Prototype in the real thickness early.

If the production intent is 1.5 mm aluminum, cut and bend that thickness for the first units rather than a random scrap gauge from the rack. On-demand sheet metal fabrication paired with CNC-machined inserts is a common path when you need both thin skins and precision bosses. For very low quantities, laser-cut blanks plus hardware can beat waiting on hard tooling, then you graduate to progressive dies only after the interface freezes.

Common RFQ mistakes with gauge callouts

Most requotes start from ambiguous thickness.

Avoid: saying only “18 gauge” without alloy; mixing steel gauge with aluminum stock; omitting coating thickness; forgetting that galvanized decimals differ; and leaving bend relief or hole-to-bend rules unspecified. Include quantity breaks (1 / 10 / 50) because nesting efficiency changes with blank size and thickness.

Reading galvanized and stainless rows on a gauge chart

Do not reuse the carbon-steel column for coated or stainless stock.

Galvanized sheets are often listed with different decimals because the zinc layers add thickness relative to the base metal conventions used in some charts. Stainless tables likewise diverge. Metal Supermarkets documents these family differences clearly on its public gauge chart—use the matching table, then still put millimeters on the drawing.

If your enclosure will be powder-coated CRS, decide whether the governing thickness is bare metal or coated stack-up for fits. Hinge clearances and PCB standoff heights are unforgiving when coating was forgotten in CAD.

Flat-pattern and bend-table discipline

Gauge errors show up first in the flat.

Bend deductions and K-factors are thickness-dependent. A CAD sheet-metal model built on the wrong decimal produces flats that look fine on screen and fail on the brake. Before releasing, measure a coupon of the intended stock or confirm the mill’s nominal. For assemblies with PEM hardware, verify grip ranges against the final thickness including finish.

When multiple thicknesses appear in one product (for example 1.0 mm covers and 2.0 mm brackets), split them into separate cut nests in the RFQ so laser parameters are not averaged incorrectly.

Hardware, welding, and assembly notes tied to thickness

Joinery choices constrain gauge selection.

Spot welds, MIG stitches, and clinching each prefer thickness windows. Thin gauges may need embosses or doublers at fastener locations. Thick gauges may need larger bend radii and more press tonnage. If fabricated assemblies are in scope, include exploded views and torque specs so the fab quotes welding fixtures once.

For prototypes, laser-cut and hardware-assembled units in the production thickness beat waiting on stamped blanks that still might change after the next IDR.

Worked examples: 11, 16, and 18 gauge in real products

Translate the chart into familiar parts.

11 gauge steel (~3.04 mm) shows up in heavier brackets, frames, and floors where dent resistance matters more than mass. Brake tonnage and laser time rise; hole-to-edge rules get more conservative. 16 gauge (~1.52 mm) is a workhorse for many chassis and covers—stiff enough for moderate spans, still friendly to PEM hardware. 18 gauge (~1.21 mm) suits lighter electronics covers and internal shields where mass and bend sharpness matter; watch connector loads and add ribs or forms if panels oil-can.

Always re-check aluminum equivalents: an “18 ga look” in aluminum may be a different decimal and a different stiffness. When in doubt, prototype the millimeter thickness you will buy in production, not the nearest scrap on the rack.

Specifying thickness tolerances and inspection

Nominal gauge is not an acceptance band.

Write an explicit thickness tolerance on critical skins (for example 1.20 ± 0.05 mm) and measure incoming sheets. For structural brackets, record thickness on the FAIR with the same seriousness as hole positions. Engineers Edge and CustomPartNet tables are starting points for nominals; your PO tolerance is the contract. If a supplier substitutes 1.5 mm for 1.2 mm “because it was in stock,” assembly stack-ups shift—even when the gauge nickname sounded close.

Conclusion

A sheet metal gauge chart is a translation tool, not a design standard. Convert 11, 16, and 18 gauge callouts into inches and millimeters for the exact alloy family, put decimal thickness on the print, and design bends and fasteners around that number. Doing so keeps laser and brake quotes comparable across US and China supply bases.

Next step: Send flat patterns or 3D sheet-metal models for a fabrication quote at Request a Quote, or email projects@6cproto.com / WhatsApp +86 180 2219 4001.

FAQ

What is 18 gauge steel thickness in mm?

About 1.21 mm (0.0478 in) for standard steel sheet using common Manufacturers’ Standard Gauge tables. Confirm with the mill cert for critical fits, and do not assume aluminum or stainless share that decimal.

Why is aluminum 18 gauge thinner than steel 18 gauge?

Different gauge systems evolved for different metals. Always convert with the chart that matches the alloy family, or specify millimeters directly on the drawing.

Can I order sheet metal in China using only US gauge numbers?

Many shops will interpret common gauges, but millimeter callouts reduce errors. Dual dimensioning (mm governing) is the clearer RFQ style for cross-border work.

Does thicker gauge always mean a stronger enclosure?

Thicker stock raises bending stiffness, but ribbing, bend strategy, and fastening often matter more than a one-gauge jump. Validate with a prototype in the intended thickness.

How should powder coat be handled on thin gauges?

Account for coating build on hole diameters and mating flanges. Note cosmetic Class requirements and masking needs so the fab and finisher quote the same part.