Michael Wang

Founder & Mechanical Engineer

As the founder of the company and a mechanical engineer, he has extensive experience in advanced manufacturing technologies, including CNC machining, 3D printing, urethane casting, rapid tooling, injection molding, metal casting, sheet metal, and extrusion.

Table Of Contents

Explore Sheet Metal Processes & Supplier Selection

Water found inside an enclosure does not identify which part of its riveted joint leaked. It may have passed through a fastener, around the head, between the sheets or through another opening entirely. The sealed blind rivets vs open end rivets decision therefore begins with the complete barrier, not with the word sealed on a product description.

A closed end body can address a leakage route that an ordinary open construction leaves available, but an enclosure still needs a defined joint geometry and acceptance test. This guide focuses on that distinction. Select the exact fastener, assemble it in the intended stack and test the finished boundary under the relevant conditions before assigning a sealing claim to the product.

The useful comparison is therefore a boundary drawing: identify the wet side, the dry side, the fastener body and every interface connecting them. Record whether leakage is unacceptable during immersion, spray exposure or a pressure differential. These are distinct service conditions, and an installation accepted for one should not inherit approval for the others.

Closed end construction and mandrel retention

A closed end blind rivet has a body termination that differs from an ordinary open end construction. This can support sealing and mandrel retention in a product designed for those functions. Stanley’s POP closed end product information describes a particular cup shaped design and its claimed performance. Those statements apply to that product, not to every rivet sold with a similar family name.

Treat retained mandrel behavior as a separate selection attribute. A loose stem can matter inside electrical equipment even when water exposure is not a concern, while a retained stem does not by itself establish the sealing of the surrounding sheets. Specify both requirements if the application needs them.

Compare complete part numbers, materials and head styles rather than photographs. An apparently identical head can conceal a different body, stem or usable grip interval. If a supplier proposes an alternative, require documentation for the relevant construction and performance instead of accepting the words sealed type as proof of equivalence. Keep the approved designation on the assembly bill of materials.

Formed metal bracket with bent tabs, cutouts and mounting holes
Bent tabs and mounting holes make tool access and joint location part of assembly planning.

Stack grip and installation

The selected fastener must cover the actual assembled grip, including retained coatings, washers and other layers. A closed end rivet that is unsuitable for the stack does not become acceptable because the joint needs sealing. Check the minimum and maximum thickness against the exact product data, then verify the installed formation.

Stanley’s breakstem riveting catalog documents distinct product families and their selection information. Use the applicable row rather than transferring an open end product’s length or hole recommendation to a closed construction. The installation tool and nosepiece must also suit the chosen fastener.

Bring sheets together in their intended condition before setting. An uncontrolled gap can leave a leakage path between the layers even if the rivet itself forms correctly. Define temporary clamping, hole preparation and any sealing compound in the sheet fabrication and assembly plan. If the sealing layer is compressible, qualify its installed and aged condition rather than selecting grip from the free thickness alone.

Leak path through the complete joint

Follow the potential fluid route across the entire joint. A path may run through the fastener, beneath its head, along the hole wall or between overlapping sheets. Blocking one route can leave another unchanged. This is why a fastener level sealing statement cannot automatically establish an enclosure level result.

Check the head seating surface, hole condition and the continuous overlap seal where one is required. A bead of sealant placed near the rivet is not necessarily a continuous barrier; its geometry, cure and compatibility need their own specification. Coatings can also crack or lift locally during installation.

The POP fastener catalog is useful for distinguishing fastener construction and installation requirements, but the designer must define the assembled leakage boundary. Show which surfaces are wet, the direction of pressure or splash and the areas that must remain dry. Include adjacent seams, drains and cable entries in a complete enclosure assessment so a failed test is not attributed to the rivet merely because it is visible near the water.

Validate sealing in the actual assembly

Test the actual assembly under a written method that reflects the required claim. Identify the test medium, pressure or exposure, duration, orientation, conditioning and measurable acceptance. A brief splash observation and a pressure leakage test answer different questions; neither should be renamed as the other.

Use representative production holes, materials, coatings and sealant conditions. A carefully prepared flat coupon can help isolate fastener behavior, but it may not reproduce a curved flange, formed distortion or an interrupted seal in the finished enclosure. Qualify those differences deliberately.

Record the location and nature of any leakage before disassembly. Where practical, use a diagnostic sequence that separates the fastener route from the sheet interface without changing multiple features at once. Agree the required evidence for the fabricated assembly before testing. An apparently dry exterior is not sufficient if the criterion concerns internal ingress, and a damp interior does not prove which path failed without additional observation.

Metal components with machined bores, flanges and pockets
Finished interfaces need their own dimensional requirements after joining.

Rivet stack and sealing interfaces on the joint drawing

A joint section should connect stack thickness, fastener formation and installation access. Include the tool body and the blind side space, not only the finished head. A sealed fastener that cannot be installed squarely in the assembly has not solved the manufacturing problem.

Drawing item Open end comparison Closed end comparison Evidence needed
Fastener construction Confirm through-body path Confirm exact closed design Product documentation
Stack and grip Match actual layers Match actual layers Stack interval and datasheet
Head seating Assess surrounding interface Assess surrounding interface Seat and hole examination
Installation access Tool and formed tail envelope Tool and formed tail envelope Assembly section
Leakage claim Validate proposed sealing system Validate complete barrier Representative assembly test

Stanley’s installation tool information provides the appropriate system context. A tool that can pull a fastener is not automatically suitable for every nosepiece, material or restricted approach in the final assembly.

Show the retained mandrel and blind-side envelope on that section. This catches interference with adjacent walls before a successful flat coupon is mistaken for an installable enclosure joint.

Leakage trials with the production overlap

Consider a hypothetical enclosure whose lap joint uses two coated sheets and a retained sealing strip. Assume the design requires the interior to remain dry during a defined water exposure, but no fastener has yet been approved. Build a coupon that reproduces the hole preparation, overlap, strip placement and actual installation access.

First document the stack interval and select a candidate whose grip covers it. Then set the fasteners using the proposed production tooling. Photograph the joint before exposure and retain the sample identity, coating condition and sealant cure history. Test the coupon under the approved method, observing where water first appears.

Next test the complete enclosure, because corners, seam terminations and adjoining features can create routes absent from the coupon. If the coupon passes and the enclosure fails, investigate those differences before changing fastener type. The example deliberately supplies no universal pressure, time or acceptable leak rate: those values must come from the application requirement and the claim the finished product is intended to meet.

Separate leakage, seating and load acceptance

Sealing, strength and appearance need distinct acceptance criteria. A joint can remain dry during an exposure yet have inadequate resistance to service loads. Conversely, a structurally acceptable joint may leak at a sheet interface. Inspect the installed fastener and test the required assembly functions without allowing one result to stand for all of them.

Product specific stem behavior also matters. Stanley’s Monobolt construction information describes a structural blind rivet with a particular locking system; it should not be treated as a generic description of every closed end rivet. Select construction from the actual duty rather than assuming closed, structural and retained stem are interchangeable terms.

Define any deformation, cracking, coating damage and head seating limits through the inspection requirements. After a leakage failure, preserve the joint before drilling out the fastener. Removal changes the hole and interfaces, which can destroy useful evidence or make a subsequent replacement test unrepresentative of an untouched production assembly.

Coordinate-measuring probe above a round component held on a fixture
Locate the accepted assembly on the references specified for inspection.

Leak paths to document before ordering

The RFQ should identify the exact joint section, materials, stack range, hole condition and access restrictions. State whether the requirement concerns water ingress, air leakage, retained stems or a combination. Provide the applicable test method and acceptance rather than asking for a waterproof rivet without defining the assembly claim.

Where sealing compound is used, identify its location, compatible surfaces and required condition before testing. State whether coatings are applied before or after assembly and how damaged protection is restored. These details affect both leakage and corrosion and should remain part of the controlled manufacturing package.

Clarify what evidence is expected from a coupon and what must be demonstrated on the complete product. Require approval for changes to fastener construction, head style, grip, hole preparation or sealing materials. A purchasing substitution that preserves nominal diameter can still alter the barrier. Keep installation tooling and inspection instructions synchronized with the approved fastener so the qualification remains connected to the assembly actually being delivered.

FAQ

Does a sealed blind rivet make an enclosure waterproof?

It can address a fastener related leakage route, but the complete enclosure also includes sheet interfaces, seams, corners and other openings. Define the required exposure or leakage claim and test representative finished assemblies. The selected fastener must be installed within its specified stack and hole conditions. Do not extend a manufacturer statement about an individual fastener into an unrestricted enclosure claim, especially when the actual joint uses different materials, coatings or sealing compounds.

Can sealant make an open end rivet equivalent to a closed end design?

A validated sealing arrangement may meet a particular assembly requirement, but equivalence cannot be assumed from the presence of sealant alone. The material, placement, cure, service exposure and mechanical behavior all need consideration. Closed construction can also have stem retention attributes that a sealant application does not reproduce. Compare the required functions separately, then qualify the proposed joint under the intended conditions rather than describing two different fastening systems as automatically interchangeable.

Can a leaking rivet simply be replaced and retested?

Replacement may be part of an approved repair, but removal can enlarge the hole, damage coatings or disturb the surrounding seal. Inspect the affected features and document the repair method before treating the retest as representative. A repaired joint and a new production joint may need different acceptance evidence. Preserve the original failure observations first, because drilling out the fastener can remove the clues needed to distinguish leakage through the rivet from leakage between sheets.

Conclusion

Choose a closed end construction when its documented features address the required fastener functions, then verify the complete joint. Grip, installation access and stem behavior remain important even when sealing is the primary concern. Map leakage paths through and around the fastener so a blocked body passage is not mistaken for a complete barrier.

Use coupons to investigate specific interfaces and finished assemblies to establish the product level result. Keep sealing, load capacity and local damage as separate acceptance items, with the test conditions stated explicitly. For an assembly review, send the joint section, selected fastener and leakage acceptance requirements for quotation. Those details let manufacturing assess an observable target and prevent the word sealed from carrying a claim that the finished enclosure has never demonstrated.