Explore CNC Cost, Tolerances & Supplier Selection
Nylon is tough, wear resistant and inexpensive, which makes it a common choice for machined parts. It is also hygroscopic: it absorbs moisture from the air, swells as it does, and changes size after the drawing has been signed off.
Can plastic be CNC machined?
Yes, and nylon is one of the most common plastics for it.
Machining is often the fastest route to a plastic part at low volume, because no tooling is required and design changes are absorbed by editing the program. Nylon machines well with sharp tooling, producing a tough part with good impact resistance and sliding wear behaviour. What makes it different from metals is that the material continues to change after machining, so the process has to account for behaviour rather than only geometry.
The practical difference shows up in three places. Cutting generates heat, and nylon’s low thermal conductivity keeps that heat local, softening the surface if feeds are too gentle. Chips are stringy and tend to wrap, so chip control matters. And the part’s dimensions depend on its moisture content, which changes with the environment it sits in rather than with anything the machinist did.
Why moisture absorption matters more than machining
Nylon absorbs water from humid air, and as it does, the material swells. The effect is not trivial: a long part can grow enough to take a fit from snug to tight, and a hole can close enough to reject an inserted component. Because the change is gradual, a part measured immediately after machining and the same part measured after a week in a humid workshop will give different numbers.
| Factor | Effect on a machined nylon part | Practical response |
|---|---|---|
| Humidity during machining | Part grows after machining | Condition stock before finishing where possible |
| Wall thickness | Thicker sections absorb more slowly but move more overall | Keep sections uniform |
| Measurement timing | Results depend on when they are taken | State the conditioning period in the specification |
| Long thin parts | Dimensional change accumulates over length | Control the moisture content, not only the tolerance |

Which nylon grades machine best
Unfilled nylon, usually supplied as PA6 or PA66 cast or extruded stock, machines cleanly and offers good toughness and wear resistance at modest cost. Cast grades machine more uniformly than extruded ones because they have less internal stress, which matters on parts with close tolerances or thin walls. Filled grades, with glass or molybdenum disulphide, improve stiffness and wear behaviour but are abrasive to tooling and produce a rougher finish.
Grade selection follows the requirement rather than the price. A sliding bushing benefits from a filled or internally lubricated grade; a part that must absorb impact benefits from unfilled material; a part exposed to sunlight needs a UV-stabilised grade, since nylon degrades under ultraviolet light without protection. Material property data is published by ASM International.
What the best plastic for CNC machining is, in practice
There is no single answer, because the best material is the one that meets the requirement at acceptable cost. POM, known as Delrin, is often chosen for precision mechanical parts because it is dimensionally stable, easy to machine and has low friction. PEEK is chosen for extreme temperature and chemical resistance at much higher cost. ABS and acrylic serve appearance and prototyping applications. Polycarbonate is chosen for impact strength and clarity. Nylon offers toughness and wear resistance at moderate cost, with moisture absorption as its main complication.
The selection logic is therefore a process of elimination. Temperature first, because it rules out most plastics immediately. Chemical exposure second, because it eliminates whole families. Mechanical requirement third, whether the part must resist impact, slide against another surface or hold tolerance. And cost last, because choosing on price alone usually means revisiting the decision later. Materials and their properties are described under materials.
Designing a nylon part that holds
Four design choices improve the outcome. Keep wall sections uniform, because uneven sections absorb moisture at different rates and distort. Avoid sharp internal corners, which concentrate stress in a material that is notch sensitive. Allow generous clearance on any fit that involves a tight tolerance, because the part will move with humidity. And where a part must hold a very tight dimension, consider specifying a conditioning period or a moisture-controlled environment rather than an unrealistic tolerance.
Two drawing notes are worth adding. State the measurement condition for critical dimensions, since nylon’s size depends on its moisture content and the ambient conditions. And identify which features are functional, because tolerance spent on non-functional surfaces in a moisture-sensitive material is difficult to deliver and easy to waste. Drawing conventions follow ASME standards, surface terminology follows ASTM Committee B08, measurement practice is described by the NIST Manufacturing Extension Partnership, and process and waste obligations are set out by the US EPA.
Machining parameters that produce a clean part
Sharp tooling with a positive rake, higher spindle speeds and generous feed rates produce a clean cut in nylon. Dwelling creates heat and a smeared finish, so continuous cutting is preferable to slow, cautious passes. Clamping pressure should be distributed rather than concentrated, because nylon marks and compresses under point loads. Where coolant is used it should be consistent, since temperature variation changes dimensions in the same way moisture does.
Finishing options are limited by the material. Painting nylon requires surface preparation because of low surface energy, printing behaves similarly, and solvent bonding is unreliable. Where a joint is needed, mechanical fastening or inserts are the practical answer. Machining and molding alternatives are described under CNC machining and injection molding.

Send the part with the tolerance that must hold and the environment it will see, and request a nylon machining quote with the conditioning note included.
FAQ
Can plastic be CNC machined?
Yes. Machining is usually the fastest route to a plastic part at low volume, since no tooling is needed and changes are made in the program. Plastics behave differently from metals, so heat, chip control and dimensional movement after machining all need accounting for.
What is the best plastic for CNC machining?
It depends on the requirement. POM suits precision mechanical parts, PEEK extreme temperature and chemicals, polycarbonate impact and clarity, and nylon toughness and wear resistance at moderate cost. Temperature and chemical exposure usually eliminate most options first.
Why do machined nylon parts change size?
Nylon absorbs moisture from the air and swells as it does, so dimensions depend on conditioning and the surrounding humidity rather than only on the machining. Cross-section, wall thickness and measurement timing all affect the result.

