← Manufacturing Materials Guides

Engineering decisions, organised

Injection Molding Materials

Choose a molding grade by mechanical behavior, temperature, shrinkage and the intended validation requirements.

Updated October 11, 2026 · 17 material resources

The resin decides the tool as much as the part

A molding grade is not a drop-in substitute. Each resin brings its own shrinkage, melt temperature, viscosity, corrosivity and abrasiveness, and the tool has to be built for it. Amorphous resins such as ABS, PC and PS shrink by roughly 0.4 to 0.8 percent; semi-crystalline grades such as PA, POM and PP shrink by 1 to 2.5 percent, and the shrinkage varies with wall thickness and flow direction. The cavity is cut to compensate, which is why a late change of grade is expensive rather than inconvenient.

Corrosivity and abrasion matter at the tool steel level. PVC releases acid at melt temperature, so the mold needs corrosion-resistant steel and often chrome plating. Glass-filled grades wear gates and cavity edges, which rules out soft tooling for a long run. A grade chosen for its data sheet alone can double the tool cost.

Injection molded PC/ABS housing with moulded ribs, bosses and a textured surface
PC/ABS behaves like neither parent: easier to mold than PC, tougher than ABS. Blends are chosen for that middle ground, and the shrinkage data still has to come from the grade supplier.

Amorphous and semi-crystalline behave differently

Amorphous resins are transparent or translucent, shrink less and hold tolerances more predictably, but they soften gradually and are sensitive to stress cracking. Semi-crystalline resins are opaque, tougher and resist fatigue and chemicals better, but they shrink more, warp more and need higher melt temperatures. The choice changes the wall sections that will mold cleanly, not just the properties in the data sheet.

Drying is part of the grade, not the process. PA, PET, PC and PEEK absorb moisture and hydrolyse if they are molded wet, which shows up as splay, weak knit lines and brittle parts. The dryer specification belongs next to the material specification.

Black injection molded plastic part with moulded features and a uniform matte finish
Pigment, additive package and grade all affect flow and shrinkage. Two black parts that look the same can need different gates and different packing.

What to settle before the resin is ordered

Three questions decide most of the outcome. What does the part have to survive — temperature, chemical, UV, impact, sterilisation? What tolerance does it actually need, given the shrinkage of the candidate grades? And does the part carry a regulatory obligation — food contact, medical grade, flame rating — that narrows the list to a handful of grades with documentation?

Answer those first, then compare grades. A shortlist of two resins tested on the real tool is cheaper than a specification that has to be revisited after the first shot.

Where the grade and the defect meet

Most molding defects are a conversation between the resin and the geometry. Sink marks appear where a thick section cools last, and the resin that sinks most is the one with the highest shrinkage. Warp appears where shrinkage differs across the part, which is why glass-filled grades are the usual suspects and why gate position matters as much as wall design. Weld lines form wherever two flow fronts meet, and they are weakest in exactly the resins that are otherwise toughest.

That is the practical argument for choosing the grade before the wall sections are final. A part designed around a low-shrinkage amorphous resin may need different ribs, a different gate and a different packing profile if the grade changes to a semi-crystalline one after the first trial.

Find the guide for your next decision

Follow the guide that matches the feature, failure mode or project decision you are working on.

POM (Delrin)

Low friction, high stiffness and excellent machinability; the default for gears, bushings and precision parts.

TPU

Flexible, abrasion-resistant elastomer for seals, grips and wheels; needs generous draft and slower cycles.

PEEK

High temperature, chemically resistant and expensive; requires hot-runner tooling and careful drying.

PC

Transparent and tough, but its high melt temperature and stress cracking drive gate and draft decisions.

PVC

Rigid or plasticised, cheap and flame resistant; the corrosive melt dictates corrosion-resistant tool steel.

ABS

The workhorse engineering resin: easy to mold, paintable and glueable, with moderate chemical resistance.

PET

Clear, strong and recyclable; needs thorough drying to avoid hydrolysis and brittle parts.

PP

Light, inert and fatigue resistant; high shrinkage and low stiffness make wall design critical.

HDPE

Food safe, chemical resistant and cheap; soft surface and high shrinkage affect tolerance and ejection.

LDPE

Softer than HDPE and used for flexible lids and closures; low stiffness limits structural use.

PTFE

The most chemically inert plastic, but it does not melt-process like a normal resin; usually machined or compression molded.

PEI

Amber, high-temperature resin with good electricals; high melt temperature and a narrow process window.

HIPS

Cheap, easy to mold and paint; used for housings and disposable parts rather than engineering loads.

PC+GF

Glass-filled polycarbonate: stiff and stable, abrasive to the tool and anisotropic in shrinkage.

CPVC

For hot-water and chemical plumbing; the corrosive melt means corrosion-resistant tooling is required.

PC+ABS

A blend with easier processing than PC and better toughness than ABS; common in electronics housings.

TPU

The overmolding grade bonds to a rigid substrate and still needs mechanical interlocks.

Before you release the project

  1. Define the function, environment and the question this batch must answer.
  2. Specify material grade, geometry, quantity, finish and the dimensions that control fit.
  3. Agree the inspection method and the evidence required to accept the parts.
  4. Record the drawing revision and approval before production begins.

Common planning questions

Can I choose a material by name alone?

Specify the grade, condition, process and required properties. A shared polymer or alloy family name does not establish identical performance.

Which material records should I request?

Request the records relevant to the project, such as grade identification, material certificates, property data or compliance declarations, and confirm how each relates to the supplied parts.

Move from guidance to a reviewed project

Send the CAD model and drawing with material, quantity, finish and inspection requirements. Use the relevant service page to review the available manufacturing route.

Review material optionsRequest a project review